求助powermill,米克郎機床海德漢系統的后處理

zhanglei113513

求助powermill,米克郎機床海德漢系統的后處理，請哪位大哥奉獻一下，本人不勝感謝。這個是本人的QQ郵箱27300165@QQ.com

vinney777

呵呵，有點無能為力了

694865935

上傳兩個我用過的，都是TNC-I530的控制器，一個機型是HSM400，還有一個是VCP600，不多說，上附件，

694865935

海德翰系統除了用它自己的格式，就是L代碼，也支持ISO代碼，不過采用ISO代碼要注意幾點
' E! r; S% @) o7 m8 a因為海德翰系統如果使用ISO代碼，要求每行都定義完整的G代碼，它不像法蘭克和三菱那有，碰到模態指令就是記憶前一條的G代碼，所以每段都要求完整的格式，比如說
N0001 G02X-7.211Y-4.132R4.469*
N0002 X-7.632Y-5.141R5.91*   如果在法蘭克和三菱機上，N0002這一行是可以讀的，會記憶0001里的G02，按照0001里的G02來走。但是在海德翰系統上，就得把0002這一行也要加上G02，不能省略，不然就報警出錯了，像下面這個格式就能跑了

- m% E! S* f* xN0001 G02X-7.211Y-4.132R4.469*
N0001 G02X-7.632Y-5.141R5.91*
, _* K1 c# M6 z
" w* }7 O* I+ S6 K, o$ H另外，海德翰系統的不讀K，但支持圓弧走R，所以走圓弧麻煩請定義成R形式的。
  u* y' \% H9 {" g5 o! }. E0 ]2 g
6 l2 d% F( Q. x生成的NC程序副檔名為.i   如E50. i之類

7 ]. t9 b1 T# m/ ~/ i* w以下是具體的一個加工程序請參照，謝謝！第一把刀T09是兩個刀路合并的，走完第一個刀路后抬到刀具初始下刀點，再開始走第二條程序。
" z" y: h& K  v% L9 S! g* I9 P


%O0001G71*      程序頭
. T4 r: F7 C8 k;(TOOL DATE MON SEP 24 09:43:47 2012)*     NC程序生成時間
;(TOOL TYPE DIA=8.0000,FLAT)*             刀具信息
# M0 c1 r, k( l& n$ l9 S: \! w5 kN0001G17T09S10000*         換刀指令
' d$ e3 ?7 n- _& D6 p6 l0 f7 e* ?+ }N0002M03*
% w: S4 Z- q+ N( J! [1 l& ~- aN0003G4F20*
N0004G583Q350=+0Q361=+3Q362=+0.01Q359=+0*            
6 w% k% ]  @( U1 s3 F5 t; @N0005G00G90G40*
N0006G62T0.005*
N0007M03*         從N02-N07為紅外量刀器動作時間，可以固定成這個格式。
0 V+ j4 H, j& R6 bN0008G00G17G90X0.Y0.*     開始加工
N0009Z100.*
, l6 ^  G0 F: Z! XN0010S10000M03*
! ~% ?( t& y, d& P7 I+ n  g3 q& SN0011G00X-84.526Y7.849*
& u% X+ V) D* h6 n% DN0012G00Z4.*
N0013M08*     開切削液
4 ?# ]; ?7 [, s4 I/ XN0014G01Z-1.F1500*
) ^9 ]: J9 v! |& }& K. z8 MN0015G01X87.569F2000*
N0016G01X-84.526Y2.849*
N0017G01X87.569*
$ F4 p( M5 ]$ I! O( {N0018G01X-84.526Y-2.151*
7 a- l0 n! P% J' ?/ M* i- WN0019G01X87.569*
+ C2 J# i& S% F' N+ l, b; Q. FN0020G01X-84.526Y-7.151*
  K( I# P3 ~0 ]/ v; Y% P. l6 aN0021G01X87.569*
N0022G01X-84.526Y-12.151*
N0023G01X87.569*
9 u. r0 S5 m9 C0 o# Q% `) _N0024G01X-84.526Y-17.151*
N0025G01X87.569*
N0026G01X-84.526Y-22.151*
N0027G01X87.569*
N0028G00Z10.*
N0029M09M05*     關水，主軸停轉（因為第二條刀路的S不一樣，出于保護機臺，主軸先停止）
( J. Z: {* o9 O1 T7 }- P1 _# KN0030G00Z100.*      抬刀到刀具初始Z位置（這條程序中我編程時設的刀具初始位置是0，0，100）
) t( s- Q  {4 A0 `0 `) R, L* b, O1 yN0031G00X0.Y0.*     抬刀到刀具初始XY位置
N0033S13000M03*      開始加工第二條刀路，按第二條刀路設定的主軸轉速啟動
N0034G00X69.*
+ U4 c% f- e, b. {N0035G00Z4.*
) ?5 Y5 m% m$ B0 }  g9 I: cN0036M08*         重新開水
* {; t3 d7 m2 I7 tN0037G01Z-1.F1500*
0 M/ D& O' U' c! |N0038G01Y5.F1000*
6 ~& W4 r( I0 _& ]) LN0039G03X64.Y0.R5.*
! l$ g- R& [' ^N0040G01Y-44.*
N0041G01X-64.*
' D  Y% A$ F% ~+ r) _N0042G01Y44.*
N0043G01X64.*
3 |1 _! Y7 A) D& U$ n) QN0044G01Y0.*
N0045G03X69.Y-5.R5.*
0 O% Q9 L# ?/ RN0046G01Y0.*
N0047G01Z-2.*
  E$ L6 U- K4 @N0048G01Y5.*
N0049G03X64.Y0.R5.*
3 i8 A& K, n. T% ~9 n7 iN0050G01Y-44.*
. A0 S. \) B9 E. s+ o# {8 ?9 iN0051G01X-64.*
N0052G01Y44.*
7 ]% N$ a4 @) l# D# @# `8 U. _N0053G01X64.*
N0054G01Y0.*
5 L; C8 I% B- Z7 V2 D! g5 T5 dN0055G03X69.Y-5.R5.*
  S/ G0 C$ ]& v3 E1 mN0056G01Y0.*
N0057G01Z-3.*
4 i; j& W1 t- l8 r) b5 vN0058G01Y5.*
; D7 E9 l# a3 j+ Q9 UN0059G03X64.Y0.R5.*
N0060G01Y-44.*
: _- v5 ~& D9 u9 [+ q: t7 EN0061G01X-64.*
7 P, J- Z- b1 j3 r- b! fN0062G01Y44.*
; f8 K! ]4 O* C4 n- r9 jN0063G01X64.*
N0064G01Y0.*
N0065G03X69.Y-5.R5.*
N0066G01Y0.*
' j5 B% h& Z$ W, \. q6 u3 Z) `N0067G00Z10.*
N0068M09M05*
N0069G00Z100.*
N0070G00X0.*
/ i: @, l& e8 dN0071M140MBMAX*   走完第一把刀，抬起Z軸到極限范圍，準備換刀
;(TOOL DATE SAT SEP 22 15:35:29 2012)*
) t5 ]5 Z2 j) X* x8 j;(TOOL TYPE DIA=6.0000,FLAT)*
/ s) v) u  s, z! A1 H. Z/ ]9 WN0072G17T08S15000*    換第二把刀8號刀
. |; K( U& m7 mN0073M03*
N0074G4F20*
N0075G583Q350=+0Q361=+3Q362=+0.01Q359=+0*
N0076G00G90G40*
8 O$ E6 t8 X7 E( eN0077G62T0.005*
N0078M03*        量刀
N0079G00G17G90X0.Y0.*
  {  a' X) p3 N- rN0080Z100.*
N0081S15000M03*
1 C& Z9 ?9 M( E" aN0082G00X0.347Y2.99*
N0083G00Z4.*
2 C6 P) a. S' `N0084M08*
N0085G01Z-1.F1500*
3 V: X, s0 \1 J& bN0086G01X-0.141Y2.988Z-1.026F1000*
! c2 E+ G: G; d" Z! J% S% ~/ sN0087G01X-0.623Y2.906Z-1.051*
N0088G01X-1.085Y2.748Z-1.077*
8 m: v0 W4 Y' k  e  m5 Q1 }N0089G01X-1.516Y2.516Z-1.103*
& {4 ?/ n; h- ^1 _, j/ G7 uN0090G01X-1.903Y2.218Z-1.128*
. J  P, _' }9 K+ @: w1 m/ h! [# FN0091G01X-2.236Y1.861Z-1.154*
7 k/ a5 G- k* G: U$ s" NN0092G01X-2.507Y1.454Z-1.179*
1 U6 k( d" p; i# zN0093G01X-2.709Y1.009Z-1.205*
4 r7 l1 @; ]% KN0094G01X-2.835Y0.537Z-1.231*
N0095G01X-2.884Y0.05Z-1.256*
N0096G01X-2.852Y-0.437Z-1.282*
N0097G01X-2.742Y-0.914Z-1.308*
N0098G01X-2.556Y-1.365Z-1.333*
1 \- f  e/ i3 S( F+ eN0099G01X-2.299Y-1.781Z-1.359*
N0100G01X-1.978Y-2.15Z-1.385*
( b/ |- k; a0 v6 d1 k$ J: S4 K9 gN0101G01X-1.601Y-2.461Z-1.41*
N0102G01X-1.179Y-2.707Z-1.436*
" v8 q/ k2 I- |2 I3 ^. ^- n; O/ SN0103G01X-0.722Y-2.882Z-1.462*
/ F$ r3 \9 i- iN0104G01X-0.244Y-2.979Z-1.487*
" u- C# l% F; u  O+ VN0105G01X0.245Y-2.998Z-1.513*
1 P" d/ K% }. B" l$ q$ ^# LN0106G01X0.73Y-2.938Z-1.538*
' f( A5 W; o# j) a4 A# \) ]N0107G01X1.198Y-2.799Z-1.564*
N0108G01X1.638Y-2.586Z-1.59*
! t/ l' @4 J7 @& `( W, kN0109G01X2.038Y-2.305Z-1.615*
N0110G01X2.386Y-1.962Z-1.641*
N0111G01X2.675Y-1.567Z-1.667*
# P" ~5 Y, Z* U! C$ fN0112G01X2.895Y-1.131Z-1.692*
: q6 b; F6 m  l$ w6 B% t& WN0113G01X3.042Y-0.665Z-1.718*
N0114G01X3.111Y-0.181Z-1.744*
" i9 I6 T; m0 H" I! `N0115G01X3.1Y0.307Z-1.769*
1 X/ J2 _9 A9 V" k9 y9 gN0116G01X3.01Y0.788Z-1.795*
N0117G01X2.844Y1.247Z-1.821*
4 l. ^9 X5 r* S7 [N0118G01X2.605Y1.674Z-1.846*
N0119G01X2.3Y2.056Z-1.872*
N0120G01X1.937Y2.383Z-1.897*
N0121G01X1.526Y2.647Z-1.923*
N0122G01X1.077Y2.841Z-1.949*
N0123G01X0.603Y2.959Z-1.974*
N0124G01X0.116Y2.999Z-2.*
9 `, I. _: C4 I, L& v7 nN0125G01X-22.523*
* h" r% b7 }' A; J4 S( D! H" l. \* X. ~N0126G01Y-2.123*
N0127G01X22.755*
N0128G01Y2.999*
* b+ m! w- U0 ?9 jN0129G01X0.116*
/ x$ A! W& n8 E# A8 yN0154G01Y17.999*
0 T, b9 d$ y' }6 WN0155G01X-37.523*
N0156G01Y-17.123*
N0157G01X37.755*
N0158G01Y17.999*
0 b0 i5 I  y3 K1 J8 D0 }0 QN0159G01X0.116*
N0160G01Y20.999*
N0161G01X-40.523*
N0162G01Y-20.123*
; c% _6 h; r1 vN0163G01X40.755*
N0164G01Y20.999*
N0165G01X0.116*
% G8 ^! R% a2 U( |4 mN0166G01Y23.999*
N0167G01X-43.523*
N0168G01Y-23.123*
N0169G01X43.755*
N0170G01Y23.999*
N0171G01X0.116*
N0172G01Y26.999*
8 z/ t; \+ I7 {0 o9 ]; YN0173G01X-46.523*
N0174G01Y-26.123*
0 p% ?! A# E) ^% lN0198G01Y-38.123*
+ ?; r" x3 c. i* A0 {N0199G01X58.755*
1 {+ C7 u' y7 Q4 JN0200G01Y38.999*
+ A2 J1 }7 Z! P  s* ?N0201G01X0.116*
N0202G01X-2.884*
N0203G01Y37.499*
# Z. w. S; N5 S" }4 sN0204G00Z10.*
( R: l7 L$ p* t# C. @N0205M09M05*
/ w; @& H/ K' x! I, dN0206G00Z100.*
: t! ]) e% I8 f  G0 t" HN0207G00X0.Y0.*
N0208M140MBMAX*
;(TOOL DATE THU SEP 20 15:07:52 2012)*
# ?2 J1 A, w8 d;(TOOL TYPE DIA=8.0000,FLAT)*
N0209G17T09S10000*        換第三把刀9號刀
' R2 @/ j) w$ {3 |4 W1 fN0210M03*
- c# U; N6 J, x! HN0211G4F20*
" i+ I. Z( L' v: b  FN0212G583Q350=+0Q361=+3Q362=+0.01Q359=+0*
N0213G00G90G40*
3 k8 X! a; L4 A& w2 ]# g  @- {N0214G62T0.005*
. V; s& k4 B! QN0215M03*      量刀
N0216G00G17G90X0.Y0.*
N0217Z100.*
N0218S10000M03*
$ [: ^8 t: ^$ c+ w- ]8 E, TN0219G00X68.*
N0220G00Z4.*
N0221M08*
N0222G01Z-1.F1500*
N0223G01Y5.F1000*
N0224G03X63.Y0.R5.*
" O, t1 B3 ^' p7 q# ZN0225G01Y-43.*
, Y2 Z  q# s2 ^9 `* C* z3 ~7 rN0226G01X-63.*
N0227G01Y43.*
) s! S% g8 u5 J: }N0228G01X63.*
% @, w% e/ P/ l9 h0 @N0229G01Y0.*
5 E2 h- b) C4 v" o' ^- DN0230G03X68.Y-5.R5.*
" x% \1 m' f9 ~, s* T$ pN0231G01Y0.*
N0232G01Z-2.*
1 w, R& g& R. |1 CN0233G01Y5.*
5 Z7 A8 {6 Q8 G, {( DN0234G03X63.Y0.R5.*
$ V, [) [& S0 X* W8 TN0235G01Y-43.*
. O, H/ _+ {- n1 m0 ?8 VN0236G01X-63.*
7 q/ [. z: y5 w; T* R# WN0237G01Y43.*
N0238G01X63.*
: L: {3 N& g; F7 lN0239G01Y0.*
  D8 T4 c  |) k( }- pN0240G03X68.Y-5.R5.*
( h4 R- B  B4 U: H, m& E: sN0241G01Y0.*
N0242G01Z-3.*
N0243G01Y5.*
8 h: j/ }+ ^  w) SN0244G03X63.Y0.R5.*
7 L8 K$ n; e4 w) ?* M7 nN0245G01Y-43.*
N0246G01X-63.*
$ W. n% R* ]" w5 a( CN0247G01Y43.*
N0248G01X63.*
N0249G01Y0.*
N0250G03X68.Y-5.R5.*
N0251G01Y0.*
' P* [" K& n9 d$ ~1 r& {% ~N0252G00Z10.*
5 g' |: o  s6 \) H5 p( W# A2 p% gN0253M09M05*
N0254G00Z100.*
N0255G00X0.*
( A' Z; |7 z, q1 H8 }; mN0256M140MBMAX*
7 \# C# @9 M* R' Y' L0 R1 u" T, M0 b
程序結束，謝謝！

694865935

這個是海德翰格式的程序，產生的程序副檔名請定義成.h  如E50.h


1 V4 U% h- l- J3 g! o' @$ E3 o2 W0001 BEGIN PGM 3333 MM
5 p+ F" q5 m" W0002 BLK FORM 0.1 Z X-100. Y-100. Z-50.
0003 BLK FORM 0.2 X+100 Y+100 Z+0.05
; D4 V/ m. x8 j- p0 e7 `0 d0004 ;(F BLADE=2)
$ l: D; S6 [- k6 K( H  y9 d/ x. p0005 ;(F DIAM=8.0000,FLAT)
) w! K4 M0 o/ ?- v& t6 ]2 {+ U9 H0006 TOOL CALL 09 Z S10000   呼叫刀具
0007 M03
0087 CYCL DEF 9.0 DWELL TIME
$ y+ {! H; x6 z. V( b( ]# g# r0087 CYCL DEF 9.1 DWELL 20   這兩行是暫停20秒
0008 TCH PROBE 583 TOOL SETTING LEN ~
3 D. J. H8 Z% z, @# k7 i0009 Q350=+0  ;MEASURING TYPE ~
7 H" p: `9 J. W3 [0010 Q361=+3  ;NUMBER OF MEASURINGS ~
0011 Q362=+0.01  ;DISPERSION TOLERANCE ~
& w) {0 M' W* p2 B% C6 q; _% t0012 Q359=+0  ;ADD. LENGTH CORRECT.  這幾行是量刀，我用的是G583的指令，
+ B, }- I- p" a/ _- {! {0013 CYCL DEF 32.0 TOLERANCE
0014 CYCL DEF 32.1 T0.007  加工精度定義
9 Q% r! X8 J& z6 M& u0015 M03
0016 LX0.Y0.FMAX
0017 LZ100.FMAX
0018 LX-84.526Y7.849Z100.FMAX
0019 LX-84.526Y7.849Z4.FMAX
0020 M08
6 r" T7 T: C. l  k# r, _0021 LX-84.526Y7.849Z-1.F1500
/ f/ K$ u: a/ u( n- }' K) y0022 LX87.569Y7.849Z-1.F2000
8 X7 r: D) O7 M) B0023 LX-84.526Y2.849Z-1.
0024 LX87.569Y2.849Z-1.
- ~8 @3 N* m4 z0025 LX-84.526Y-2.151Z-1.
0026 LX87.569Y-2.151Z-1.
0027 LX-84.526Y-7.151Z-1.
0028 LX87.569Y-7.151Z-1.
6 R7 Q6 ^( c6 L$ X0029 LX-84.526Y-12.151Z-1.
0030 LX87.569Y-12.151Z-1.
0031 LX-84.526Y-17.151Z-1.
( }( c, E# ^( G  A6 ?, K: t$ g0032 LX87.569Y-17.151Z-1.
0033 LX-84.526Y-22.151Z-1.
0034 LX87.569Y-22.151Z-1.
0035 LX87.569Y-22.151Z10.FMAX
1 n" G2 u$ [. G0036 LX87.569Y-22.151Z100.FMAX
0037 LX0.Y0.Z100.FMAX
0038 CYCL DEF 32.0 TOLERANCE
# H1 b6 R( a. d$ L2 q4 g0039 CYCL DEF 32.1   這里是兩條刀路合并的，同一把刀，走完第一個刀路抬到安全起始高度
0040 LX69.Y0.Z100.FMAX
0041 LX69.Y0.Z4.FMAX
5 Z* C5 I" E+ F. i0042 M08
0043 LX69.Y0.Z-1.F1500
/ s. ]1 L( X" v% N0044 LX69.Y5.Z-1.F1000
0045 CCX69.Y0.
; s0 Q: |8 O2 W0 A0046 CX64.Y0.DR+
0047 LX64.Y-44.Z-1.
0048 LX-64.Y-44.Z-1.
0049 LX-64.Y44.Z-1.
. `8 c( {2 j: t9 `  m4 p0050 LX64.Y44.Z-1.
0051 LX64.Y0.Z-1.
0052 CCX69.Y0.
2 _) J% f" `# n* B; Z0 M! Q0 M0053 CX69.Y-5.DR+
0054 LX69.Y0.Z-1.
0055 LX69.Y0.Z-2.
# o' k3 f/ W  x: j$ J0056 LX69.Y5.Z-2.
9 G- R3 R) l9 d, u$ L1 N0057 CCX69.Y0.
1 m5 [! o) ]8 G2 d, x" f: \0058 CX64.Y0.DR+
- `* n" W. J; ~0059 LX64.Y-44.Z-2.
7 }: C( m  k6 D, C" o% x3 V! K* {0060 LX-64.Y-44.Z-2.
: e* e" M/ m, c1 B$ @" W0061 LX-64.Y44.Z-2.
0062 LX64.Y44.Z-2.
0063 LX64.Y0.Z-2.
$ c% F8 J* d2 x5 w, o$ J0064 CCX69.Y0.
6 r' Q* d# o. m0 R; H2 }, M0065 CX69.Y-5.DR+
- @3 G. ~" {/ l7 q- M0066 LX69.Y0.Z-2.
0067 LX69.Y0.Z-3.
0068 LX69.Y5.Z-3.
0069 CCX69.Y0.
9 P) {, M1 ?/ Q, h& E3 r/ ^0070 CX64.Y0.DR+
0071 LX64.Y-44.Z-3.
0072 LX-64.Y-44.Z-3.
0073 LX-64.Y44.Z-3.
0074 LX64.Y44.Z-3.
$ B) S+ r- ^. c4 @3 h8 q0075 LX64.Y0.Z-3.
0076 CCX69.Y0.
0077 CX69.Y-5.DR+
$ X: W8 h/ ~1 E0078 LX69.Y0.Z-3.
" G, A1 i/ N" ~6 k% Z. P0079 LX69.Y0.Z10.FMAX
0080 LX69.Y0.Z100.FMAX
. E8 N5 X4 ]0 ?2 F' X! S0081 LX0.Y0.Z100.FMAX     
8 E; {! Z# l) c2 C0082 CYCL DEF 32.0 TOLERANCE
0083 CYCL DEF 32.1     程序結束
- G7 N( _- g, Q, X( J0084 ;(F BLADE=2)
0085 ;(F DIAM=6.0000,FLAT)
0086 TOOL CALL 08 Z S15000 換刀
0087 M03
! q7 `- w. T! A/ P0087 CYCL DEF 9.0 DWELL TIME
0087 CYCL DEF 9.1 DWELL 20 暫停20秒暖機
0088 TCH PROBE 583 TOOL SETTING LEN ~
8 N* J" w* c8 s! X5 I0089 Q350=+0  ;MEASURING TYPE ~
, }/ ~- f0 Z) a. r% W0090 Q361=+3  ;NUMBER OF MEASURINGS ~
% M; W4 J6 h' i9 _8 R5 B$ I( v3 N0091 Q362=+0.01  ;DISPERSION TOLERANCE ~
4 D. U0 \1 s2 W/ G0092 Q359=+0  ;ADD. LENGTH CORRECT.
0 l8 t3 N2 Z8 `0 y; K' h+ p# W% T, a9 u0093 CYCL DEF 32.0 TOLERANCE
, @( d% e4 M5 E8 G8 J# F0094 CYCL DEF 32.1 T0.007
, x" [: l$ X( b3 a5 z% ^6 s0095 M03
0096 LX0.Y0.FMAX
/ ?# Y9 Y! |6 u* G/ s' r. Z  O0097 LZ100.FMAX
0098 LX0.347Y2.99Z100.FMAX
0099 LX0.347Y2.99Z4.FMAX
0100 M08
0101 LX0.347Y2.99Z-1.F1500
: }/ F9 @  D% A  T% D+ k$ t0102 LX-0.141Y2.988Z-1.026F1000
1 u! G6 n/ A' y* {/ m1 r0103 LX-0.623Y2.906Z-1.051
0104 LX-1.085Y2.748Z-1.077
0105 LX-1.516Y2.516Z-1.103
( g: d" u- y( T0106 LX-1.903Y2.218Z-1.128
0107 LX-2.236Y1.861Z-1.154
0108 LX-2.507Y1.454Z-1.179
$ D1 I4 J8 o: b% Q0109 LX-2.709Y1.009Z-1.205
# c; K" Y5 a7 M+ Z6 V5 I0110 LX-2.835Y0.537Z-1.231
& o* @3 H: C& x# L- ]; {7 a) P& R0111 LX-2.884Y0.05Z-1.256
  I- R: m' E& i/ m0112 LX-2.852Y-0.437Z-1.282
2 m) l8 i" u  o% ^& p* M1 _0113 LX-2.742Y-0.914Z-1.308
0114 LX-2.556Y-1.365Z-1.333
! W1 x; n3 ~0 N- y, C0115 LX-2.299Y-1.781Z-1.359
0116 LX-1.978Y-2.15Z-1.385
0117 LX-1.601Y-2.461Z-1.41
0118 LX-1.179Y-2.707Z-1.436
0119 LX-0.722Y-2.882Z-1.462
0120 LX-0.244Y-2.979Z-1.487
0121 LX0.245Y-2.998Z-1.513
  C% i( R) t0 T# f  x; E/ e0122 LX0.73Y-2.938Z-1.538
0123 LX1.198Y-2.799Z-1.564
* z, W) D+ ?5 i' g0124 LX1.638Y-2.586Z-1.59
5 [3 D! H0 @3 s7 [0 v0125 LX2.038Y-2.305Z-1.615
0126 LX2.386Y-1.962Z-1.641
$ n& q, d8 I( F0127 LX2.675Y-1.567Z-1.667
0128 LX2.895Y-1.131Z-1.692
0129 LX3.042Y-0.665Z-1.718
0130 LX3.111Y-0.181Z-1.744
* t9 K9 o3 ~& |+ H! P. f# U" H0131 LX3.1Y0.307Z-1.769
+ O5 c0 n9 k& l( U0 T0132 LX3.01Y0.788Z-1.795
0133 LX2.844Y1.247Z-1.821
0134 LX2.605Y1.674Z-1.846
6 h2 h- g4 K) F: p0135 LX2.3Y2.056Z-1.872
3 h, f2 E. [3 Z5 f: d+ Y0 ^0136 LX1.937Y2.383Z-1.897
0137 LX1.526Y2.647Z-1.923
3 r0 Z9 X' g/ T9 _2 z! r5 I* O+ Z0138 LX1.077Y2.841Z-1.949
0139 LX0.603Y2.959Z-1.974
0140 LX0.116Y2.999Z-2.
7 F2 n5 j; I5 |+ N1 g* a# w0141 LX-22.523Y2.999Z-2.
" E' Y5 c4 h6 I0142 LX-22.523Y-2.123Z-2.
4 A8 j! ~, H! h1 B5 G$ n! [% G0143 LX22.755Y-2.123Z-2.
0144 LX22.755Y2.999Z-2.
0145 LX0.116Y2.999Z-2.
0146 LX0.116Y5.999Z-2.
: D$ e! Z! l) ^+ ~+ d" V0147 LX-25.523Y5.999Z-2.
( y) r* o) S# M0 y0148 LX-25.523Y-5.123Z-2.
: u) Y1 X6 \% H, U9 ?5 m2 U0149 LX25.755Y-5.123Z-2.
0150 LX25.755Y5.999Z-2.
0151 LX0.116Y5.999Z-2.
0152 LX0.116Y8.999Z-2.
: b& \, ?3 `6 k0153 LX-28.523Y8.999Z-2.
# d1 ^5 O; f$ }, n* m* `1 x0154 LX-28.523Y-8.123Z-2.
0155 LX28.755Y-8.123Z-2.
0156 LX28.755Y8.999Z-2.
0157 LX0.116Y8.999Z-2.
0158 LX0.116Y11.999Z-2.
0159 LX-31.523Y11.999Z-2.
0160 LX-31.523Y-11.123Z-2.
0161 LX31.755Y-11.123Z-2.
0162 LX31.755Y11.999Z-2.
8 l/ y2 K, {( T; q4 g( y0163 LX0.116Y11.999Z-2.
* W# R4 n# k/ |& H1 ]) c) e0164 LX0.116Y14.999Z-2.
# m! l: j  ~- N% r5 f0165 LX-34.523Y14.999Z-2.
0166 LX-34.523Y-14.123Z-2.
0167 LX34.755Y-14.123Z-2.
8 s3 C' f. M- o; k* l6 L( |0 i9 c0168 LX34.755Y14.999Z-2.
+ _6 a6 F- E- W; j0169 LX0.116Y14.999Z-2.
% }  i( J9 n/ q/ B0170 LX0.116Y17.999Z-2.
0171 LX-37.523Y17.999Z-2.
0172 LX-37.523Y-17.123Z-2.
+ `5 f3 R# w) {/ U* m' W+ i# b8 N5 M2 w0173 LX37.755Y-17.123Z-2.
0174 LX37.755Y17.999Z-2.
% l  i, K+ Y/ b# E) H/ M0175 LX0.116Y17.999Z-2.
& o# V6 w* h; Z' J0176 LX0.116Y20.999Z-2.
0177 LX-40.523Y20.999Z-2.
( a8 L8 W9 B' S0 P* i: ~0178 LX-40.523Y-20.123Z-2.
# _" p+ t/ R. p* L" b2 c$ o0179 LX40.755Y-20.123Z-2.
9 @7 [$ o* r& l- g' k0180 LX40.755Y20.999Z-2.
' M/ a9 r7 O  ?$ s& v# b, l0181 LX0.116Y20.999Z-2.
0182 LX0.116Y23.999Z-2.
; D% ~+ L1 X! R2 w3 ^2 x' k0183 LX-43.523Y23.999Z-2.
) C: ]1 P3 v" Y7 z5 m2 ^' s( x0184 LX-43.523Y-23.123Z-2.
0185 LX43.755Y-23.123Z-2.
# e8 \$ {% l1 l- Y0186 LX43.755Y23.999Z-2.
0187 LX0.116Y23.999Z-2.
7 V: C# n8 v, f' m: y0 Y0188 LX0.116Y26.999Z-2.
# x+ W! @3 E2 K1 z% G0189 LX-46.523Y26.999Z-2.
  d4 F# [: R$ h. j. y; x4 H0190 LX-46.523Y-26.123Z-2.
8 z2 j! D6 B+ }6 f0191 LX46.755Y-26.123Z-2.
0192 LX46.755Y26.999Z-2.
0193 LX0.116Y26.999Z-2.
0194 LX0.116Y29.999Z-2.
0195 LX-49.523Y29.999Z-2.
' g. P" {  c6 J3 w  J$ u, P4 X0196 LX-49.523Y-29.123Z-2.
0197 LX49.755Y-29.123Z-2.
0198 LX49.755Y29.999Z-2.
0199 LX0.116Y29.999Z-2.
0200 LX0.116Y32.999Z-2.
0201 LX-52.523Y32.999Z-2.
0202 LX-52.523Y-32.123Z-2.
  Q3 n7 N' ]  m0203 LX52.755Y-32.123Z-2.
0204 LX52.755Y32.999Z-2.
2 y4 r2 d! Z( M* e% P0205 LX0.116Y32.999Z-2.
0206 LX0.116Y35.999Z-2.
9 t/ n8 g0 C, T4 W% u0207 LX-55.523Y35.999Z-2.
$ Q5 j+ U, P$ i0 Y. r0208 LX-55.523Y-35.123Z-2.
0209 LX55.755Y-35.123Z-2.
0210 LX55.755Y35.999Z-2.
# B! e  J( R7 d3 ]: u" b0211 LX0.116Y35.999Z-2.
0212 LX0.116Y38.999Z-2.
- y( }& f5 G9 ^9 V6 Z) X( a  `7 C! p0213 LX-58.523Y38.999Z-2.
% G, e$ p' G# k5 a9 ~0214 LX-58.523Y-38.123Z-2.
0215 LX58.755Y-38.123Z-2.
5 s0 ~* B' T: t9 d9 l2 B0216 LX58.755Y38.999Z-2.
0217 LX0.116Y38.999Z-2.
0218 LX-2.884Y38.999Z-2.
0219 LX-2.884Y37.499Z-2.
0220 LX-2.884Y37.499Z10.FMAX
6 X7 e, `3 C, E" G6 w0221 LX-2.884Y37.499Z100.FMAX
+ W- \* T% ^: l9 O% _0222 LX0.Y0.Z100.FMAX
0223 CYCL DEF 32.0 TOLERANCE
/ p( \- g) W! Z7 `- X0224 CYCL DEF 32.1
0225 ;(F BLADE=2)
" F3 |1 f; j+ M/ D1 E: H  p0226 ;(F DIAM=8.0000,FLAT)
0227 TOOL CALL 09 Z S10000
0228 M03
# C/ K; g8 X2 s0087 CYCL DEF 9.0 DWELL TIME
0087 CYCL DEF 9.1 DWELL 20 暫停20秒暖機
% j6 D; B8 R) a9 v0229 TCH PROBE 583 TOOL SETTING LEN ~
* H* L. d  i% D& D" @9 [& @4 G0230 Q350=+0  ;MEASURING TYPE ~
0231 Q361=+3  ;NUMBER OF MEASURINGS ~
) |* z9 f' [  |3 e5 M% o7 K+ [& w8 G0232 Q362=+0.01  ;DISPERSION TOLERANCE ~
. l( B1 L  {% o. p# S' t- Q0233 Q359=+0  ;ADD. LENGTH CORRECT.
. M3 d9 P1 u- A3 T6 r0234 CYCL DEF 32.0 TOLERANCE
1 \* ]- q  c( ~% _8 h# l/ J- ~% |. p0235 CYCL DEF 32.1 T0.007
- [! a; C; m( R4 E5 @0236 M03
9 [  f5 G8 Y' P" D8 C' D2 O0237 LX0.Y0.FMAX
0238 LZ100.FMAX
+ O0 V( e0 G2 Y  c; \8 p0239 LX68.Y0.Z100.FMAX
0240 LX68.Y0.Z4.FMAX
0241 M08
9 o- [( ~( N" V& M- ~2 T9 n0242 LX68.Y0.Z-1.F1500
6 ?5 }* C3 t/ C) G3 T; h! X0 R0243 LX68.Y5.Z-1.F1000
# o& O8 D# w  T- v0244 CCX68.Y0.
0245 CX63.Y0.DR+
0246 LX63.Y-43.Z-1.
3 {* }) f+ O/ w* Y$ e. n0247 LX-63.Y-43.Z-1.
. f) }! P+ D: v7 f0248 LX-63.Y43.Z-1.
5 l0 |& E  _) E/ T+ q  X0249 LX63.Y43.Z-1.
' L- F3 ]  B2 g) c" M+ G- b0250 LX63.Y0.Z-1.
0251 CCX68.Y0.
0252 CX68.Y-5.DR+
0253 LX68.Y0.Z-1.
# W" ~: ?2 H! O4 d  `+ q, Y0254 LX68.Y0.Z-2.
- \8 p3 C$ w% M$ P0255 LX68.Y5.Z-2.
0256 CCX68.Y0.
0257 CX63.Y0.DR+
0258 LX63.Y-43.Z-2.
0259 LX-63.Y-43.Z-2.
0260 LX-63.Y43.Z-2.
! w: a2 P/ o6 j8 e% ~0261 LX63.Y43.Z-2.
0262 LX63.Y0.Z-2.
0263 CCX68.Y0.
4 Y7 h  d4 h. w, H0264 CX68.Y-5.DR+
0265 LX68.Y0.Z-2.
, E# l8 g! p0 i3 {0266 LX68.Y0.Z-3.
# {2 i4 _1 x; x$ ~- V' r) K0 h0267 LX68.Y5.Z-3.
0268 CCX68.Y0.
0269 CX63.Y0.DR+
0270 LX63.Y-43.Z-3.
0271 LX-63.Y-43.Z-3.
0272 LX-63.Y43.Z-3.
0273 LX63.Y43.Z-3.
0274 LX63.Y0.Z-3.
1 r% U5 N+ F) w" A: t$ y/ t0275 CCX68.Y0.
0276 CX68.Y-5.DR+
2 X! f$ V/ ~! w; }, I. R$ t0277 LX68.Y0.Z-3.
4 j. {6 `' W3 Q" }1 H0278 LX68.Y0.Z10.FMAX
0279 LX68.Y0.Z100.FMAX
7 H4 h, N% D7 k" I$ o& ^0280 LX0.Y0.Z100.FMAX
0281 CYCL DEF 32.0 TOLERANCE
0282 CYCL DEF 32.1
0283 ENDPGM3333MM

djaho

上兩個月買了一床1.8M的蕾舒床墊,太失望了,做工差,只用了一個多用就開始變形了,里面的彈簧突出來了,這是床墊嗎!?還有說好送到樓下,就送到物流點就不送過來了,說要我們自提,之后聯系他們店長,說支付100元給我們,到最后還沒有支付!跟他們糾結了半個月了還是這樣子,算了,當給錢給他們的店長買藥吃!服務差,態度差,還有質量差!

1900

uop800有后處理嗎?!

zhilin.zhang

至于機床我不做表態我個人認為海德漢系統是相當不錯的，大多用于高端機上。

374601

不錯，繼續五軸的后處理

過眼云煙

都是高手，小弟剛接觸海德漢，還玩不轉